| General information | |
|---|---|
| Origin | Brand: Japan - Made in: Thailand |
| Gas | R410A |
| Type | Inverter - 2-way type (cooling / heating) |
| Cooling capacity | 2.0 Hp - 18.000 Btu/h |
| Using for rooms | Area 20 - 30 m² or 60 - 80 m³ (suitable for living room, office) |
| Power source (Ph/V/Hz) | 1 Phase, 220 - 240 V, 50Hz |
| Electricity consumption | 1.29 kW |
| Refrigerant/ Liquid Pipe Diameter (mm) | 6.35 / 12.7 |
| Maximum Pipe Length (m) | 30 (m) |
| Maximum Elevation Length (m) | 20 (m) |
| In door unit | |
| Dimensions (H x W x D) (mm) | 840 x 236 x 840 (mm) |
| Weight (Mass) (Kg) | 24 (Kg) |
| Panel | |
| Panel Dimensions (mm) | 950 x 35 x 950 (mm) |
| Panel Net Weight (Kg) | 5.5 (Kg) |
| Outdoor Unit | |
| Dimensions (H x W x D) (mm) | 640 x 800 (+71) x 290 (mm) |
| Weight (Mass) (Kg) | 45 (Kg) |
Mitsubishi Heavy ceiling mounted air conditioning FDT50VG/SRC50ZSX-S inverter (2.0 Hp) Hyper inverter series is super power-saving and quiet, with super-fast heating and cooling capabilities, suitable for installation in living rooms, bedrooms...with an area of less than 35m2.
Powerful heating power
The maximum heating power was increased thanks to the optimization of refrigerant control by the electronic throttle and the new dual-rotor compressor. The Hyper Inverter type can quickly reach the set temperature, maintaining rated heating capacity when the outdoor temperature is -150C. Effective when used immediately in cold areas.
Inverter technology saves electricity.
New advanced technology with high efficiency, powerful heating operation mode, and long pipeline. Contributing to environmental protection through energy-saving allows installing equipment (4~6HP) that can operate heating under temperature conditions down to -20ºC. In addition, design flexibility has been improved for pipe lengths up to 100m.
Airflow control mask
With four blowing doors, Mitsubishi Heavy ceiling mounted air conditioning FDT50VG/SRC50ZSX-S inverter (2.0 Hp) helps direct the airflow to prevent cold/hot air from blowing directly on people. Furthermore, it is possible to adjust the airflow separately for each wing.
Motion sensor
A motion sensor is fitted in the corner of the panel and detects the presence/absence and activity of people in the room to improve comfort and save energy of the device. Up to now, this technology is only available in ceiling air conditioner Mitsubishi Heavy and Daikin.
Independent air swing control system
Depending on room conditions, the wind direction is independently controlled in 4 tips by the separate vane control system.
Sleep timer
Set the time interval from opening to shutting down. The adjustable gap from 30 to 240 minutes (10 minutes in each step).
Drain pump 700mm
The drain pump is pre-assembled with a pipe lift of 700mm from the ceiling, allowing a free layout of the pipeline. Depending on the installation location, a 260mm hose, a standard accessory, facilitates easy installation.
Quickly check the drain trough
With the new design, it can quickly check by removing the corner cover so that checking the condition of the water pump is easy without removing the panel. In addition, locating the drain hole of the water trough is easy and convenient.
Anti-corrosion Blue Fin heatsink
Thanks to the application of Blue Fin (KS101) protective coating to the heat exchangers of the new outdoor unit models, the corrosion resistance is improved compared to the previous outdoor unit models.
Balance the indoor unit when installing
A balanced arrangement of the indoor unit installation can make without removing the panel by inspecting the access doors with removable covers at each corner of the unit. Improves operability and significantly reduces installation time.
